Spread the love

Traditional freestanding baths fall into a number of broad categories with regard to their basic shape, two other problems with equal significance are the style of foot and the type of faucet fittings required. Each of these and the main kinds of traditional tub tub shape are described below. The data in this article is about contemporarily manufactured traditional model freestanding baths not vintage baths.

Tub Foot Fashion

Traditional bathtub feet usually are available one in every of 4 broad styles though the variation within those styles can be great. Plain feet, ball and claw toes, often just called claw ft are in the form of a talon or claw gripping onto a ball which rests on the floor and takes the weight of the bathtub, lions paw toes are shaped just like the paw of a lion standing on the toilet flooring after which there are numerous more or less Artwork Deco style feet that you’ll find on a number of freestanding baths. Of those three categories the ball and claw ft are available in such large variation that the more stylised variations are barely recognisable as such with much of the detail gone. Plain ft are just like the ball and claw on the whole form however don’t have any detail on them.

Tub feet are available in numerous materials and finishes, forged iron toes must be painted, most often they’re painted black, white or the same colour as the toilet walls. Feet are also available made from brass, either with a elegant brass finish (which is commonly used with gold taps) or in electroplated chrome, gold (normally called antique gold), brushed nickel or shiny nickel. Not all traditional baths have feet. Typically feet aren’t interchangeable between baths although they may typically be that specific producers use the identical ft on or more of their baths. You should by no means buy a shower without the ft unless you already know you can get the right feet manufactured for that bath.

Roll Prime and Tap Fittings

Its necessary to know when you purchase a traditional freestanding bathtub what sort of faucets you’ll use with it and what you will need to attractively plumb them in Traditional freestanding baths are sometimes called roll prime baths, this refers to the rolling edge of many traditional model of bath. It’s not possible to mount a tap onto the rolling fringe of a roll top bath. A traditional solution to this was to drill the taps gap within the side of the bath just above the overflow the faucets used are formed to come up at right angles to the water inlet so they are in the same form as a deck mounted set of taps. These taps are called globe faucets, they often come as a pair of faucets, hot and cold. Globe faucets are solely really used these days with antique cast iron roll prime baths.

More usually these days roll top baths onto which faucets might be mounted have what’s called a tap platform. A tap platform is a flattened part of the tub edge into which faucet holes will be drilled and faucets mounted. For baths onto which taps cannot be mounted you’ll use both wall mounted or floor mounted taps. Note also that there are some contemporarily manufactured and, broadly talking, traditionally styled baths that should not have a roll high as such and onto which taps might in theory be mounted anywhere on the edge of the bath.

Traditional Single Ended

This is the best of the traditional bathtub kinds, its a degree topped tub sitting on 4 toes, in plan its rounded on the head end (where your head would go in the event you were mendacity in it) and flat on the foot end. The plug gap and overflow are at the foot finish of the bath. If it has a faucet platform that can be at the foot finish of the bath. Its distinguished from a slipper tub by being the same height throughout the top of the bath.

Traditional Double Ended

This is basically the same because the traditional single ended tub but in plan it’s rounded at both ends and the plug hole and overflow in the middle of one of many long sides of the bath. If it has a tap platform then that is also within the center along the lengthy side of the bath. Like the single ended tub it’s the same height throughout the highest of the bathtub and it sits on 4 feet of 1 fashion or another..

Slipper Baths

A slipper bathtub is a traditional single ended tub but with a the head end of the bathtub higher than the foot end. The head finish of the bathtub rises up, often with some model, to make the (heeled) ‘slipper’ form after which the bathtub is named. Traditional slipper baths sit on four ft, often with slipper baths the front feet and back ft are slightly different shapes and should not interchangeable. Brief slipper baths, 1500mm. are common in en-suites. Large slipper baths are suitable for a very luxurious and indulgent setting. Slipper baths are sometimes however not at all times fairly vast and deep.

Bateau Baths

A bateau bath is a double ended version of the slipper bathtub, whereas the slipper bath goes up at just one end the bateau is symmetrical and rises up at each ends. Just like the slipper bath its typically on 4 toes, in contrast to the slipper bathtub there should not often be completely different ft required for the entrance and back. Bateau baths are found both with and with out tap ledges for mounting taps.

Boat Baths

A ship bathtub is a bateau bathtub without ft, instead it usually has a skirt that goes all the way down to a plinth which takes the load of the bathtub (or a metal frame underneath might sometimes take the load). Like bateau baths, boat baths are available with and with out faucet holes.

Keyhole Shower Baths

These keyhole formed baths, the place the spherical finish of the tub was for a shower are very rare and there might be no non-bespoke producers of them left, though up till lately they could possibly be bought as a non-bespoke product.